Shree Swaminarayan Industries
Shree Swaminarayan Industries
Send Email
Send SMS
Search

Home » Products » Rosin Based Flux


Rosin Based Flux

Leading Manufacturer of mildly activated rosin soldering flux and rosin based soldering flux from Pune.

Mildly Activated Rosin Soldering Flux

REQUEST CALLBACK

Mildly Activated Rosin Soldering Flux
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 1 / LitreGet Latest Price

Product Details:
Grade StandardTechnical Grade, Bio-Tech Grade
UsageCommerical
Packaging Size20- 50 kg

Mildly Activated Rosin Soldering Flux is a liquid soldering flux that provides good electrical insulation with its protective resinous formulation and special activating agents gives consistently good soldering results. Mildly Activated Rosin Flux can be used for both conventional through hole and S.M.D. soldering. Its flux residue is non-corrosive and non-conductive in presence of highly insulative rosin. The low solid content of this flux the advantage of leaving lesser amount of residue on the board after soldering without compromising on good soldering results. This makes it unnecessary to clean the board by solvent or ultrasonic treatment and the boards dry and not sticky after soldering.

Merits Of Using SS –3006 Flux:


  • SS –3006 Rosin based flux is a clear solution of WW grade rosin and some mild activating agents still gives user certain advantages, as listed below
  • Not sticky
  • Low halide
  • Low residue
  • Very easy to use
  • No icicles and bridges formation
  • Very stable foaming characteristics
  • Safe residue
  • High S.I.R. value

Application:

  • SS –3006 is applicable in any of the existing wave soldering machines used in the industry today. Application of the flux can be any of the three methods: Dip, Wave, and Foam. Preheat temperature of between 850C and 950C on the component side of the board is recommended.
  • For best foaming result, the level of flux in the fluxing tank should be maintained at about 1.3 to 2.0 cm above the foaming stone. Periodic monitoring of specific gravity with a hydrometer or automatic density censoring system and addition of the appropriate amount of flux thinner is necessary to ascertain consistent soldering results.

Flux Quality:


  • In time, debris and contaminates will accumulate in the flux. This contamination will affect the quality of the flux, hence soldering. For consistent soldering performance, replace flux periodically. Before replacing the flux reservoir with fresh flux, the reservoir, fluxing attachment and aerator stone should be thoroughly clean with a suitable flux cleaner.
  • During the cleaning process, it would be as good a time to clean the conveyor belt fingers and jigs of accumulated flux residue. After cleaning, rinse all relevant parts with a suitable flux thinner.
  • Refills flux reservoir with fresh flux and allow a few minutes for foam to stabilize before resuming soldering operation


Additional Information:

  • Item Code: SS-3006
Send Bulk Enquiry

Rosin Based Soldering Flux

REQUEST CALLBACK

Rosin Based Soldering Flux
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 1 / LitreGet Latest Price

Product Details:
Grade StandardBio-Tech Grade, Technical Grade
Packaging Size20- 50 kg
UsageCommerical

Rosin Based Soldering Flux is activated for excellent soldering with good electrical insulation property of commercial type printed circuits boards. Rosin Based Soldering Flux can be used for both conventional through hole and S.M.D. soldering. Its flux residue is non-corrosive and non-conductive in presence of highly insulative rosin. The low solid content of 15 % Wt. The flux is washed off the board during soldering, so that there is practically no flux residue left on the board. This makes it unnecessary to clean the board by solvent or ultrasonic treatment and the boards dry and not sticky after soldering.

Merits Of Using Ss-2001Ra Flux:


  • Not sticky
  • Low halide
  • Low residue
  • Very easy to use
  • No icicles and bridges formations
  • Very stable foaming characteristics
  • Safe residue
  • High S.I.R. value
  • Good shining quality finishing to the solder fillets

Application:


  • SS-2001 is applicable in any of the existing wave soldering machines used in the industry today. Application of the flux can be any of the three methods
  • Dip, Wave, and Foam. Preheat temperature of between 950C and 1100 C on the component side of the board is recommended
  • For best foaming result, the level of flux in the fluxing tank should be maintained at about 1.3 to 2.0 cm above the foaming stone
  • Periodic monitoring of specific gravity with a hydrometer or automatic density censoring systems and addition of the appropriate amount of flux thinner is necessary to ascertain consistent soldering results.


Additional Information:

  • Item Code: SS-2001-RA
Send Bulk Enquiry

 
X


Explore More Products

Contact via E-mail
Contact via SMS
Shree Swaminarayan Industries
Gunvant Padalsekar (Owner)
Plot No. PAP-G-8/9, MIDC, Phase III, Near Mercedeze Benz Chakan, Tal. Khed,
Pune - 410501, Maharashtra, India
Call Us: 
Call Response Rate: 97%
Share Us :
F G T L



Home  |   Profile   |  Products  |  Site Map  |   Contact Us

© Shree Swaminarayan Industries. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited

Shree Swaminarayan Industries